Archive for the ‘Tensilkut II’ Category

Composite Tensile Test Sample Preparation

August 2, 2017

Recently, a customer sent us some composite strips to be cut into ASTM D638 Type I tensile samples.  We used the Tensilkut II, and the process was very fast and easy.

Tensilkut machines are sized for location in your testing laboratory, to be used by technicians without machining experience.  The Tensilkut II is a floor model, manually operated machine; table model Tensilkut I machines are also available for labs with less space available.  Visit our website at www.tensilkut.com or fill out the contact form below for more information on how Tensilkut can make your tensile specimen preparation easier!

Tensilkut II

July 24, 2017

The Tensilkut II is an efficient, cost effective way to prepare tensile samples.  Recently, we cut some specimens from fiber filled composites for demonstration; the attached video shows the cutting of two ASTM D638 Type I tensile bars, from start to finish, in about 8 minutes.

This video also shows measuring of the specimen during the cutting process, which is not necessary with a properly adjusted Tensilkut machine and master template, but does demonstrate the accuracy of the system.  Tensilkut machines are designed to be operated by lab personnel without previous machining experience.  Please contact us today for further information on how we can help you with your testing program.

Demonstration of the Tensilkut II

June 23, 2015

The Tensilkut II is used to easily prepare flat tensile, compression, flexural and other specimens from metals and non-metallics.  This machine is designed for operation in the testing lab by technicians without previous machining experience.

The starting blank is inserted into the Tensilkut Master Template, and the clamping screws are tightened as shown in this video.  The micrometer dial on the Tensilkut control head is set to its starting position, and a series of light passes are taken to cut the material from each side of the specimen.  When the correct tensile specimen dimensions are achieved, the micrometer dial will stop turning, thus preventing cutting an undersized test specimen.  After removing the completed ASTM E8 or other specimen from the master template, the tensile bar is ready for immediate testing.

ASTM D412 Die D Tensile Bar Preparation

May 13, 2015
Tensilkut Master Templates 50-97, 50-98 and 50-99 for preparing rubber test specimens in accordance with ASTM D412 Die D: Available for use on Tensilkut I and Tensilkut II models.

Tensilkut Master Templates 50-97, 50-98 and 50-99 for preparing rubber test specimens in accordance with ASTM D412 Die D: Available for use on Tensilkut I and Tensilkut II models.

50-99 Tensilkut Master Template in accordance with ASTM D412 Die D

50-99 Tensilkut Master Template in accordance with ASTM D412 Die D

50-98 Template: ASTM D412 Die D

50-98 Template: ASTM D412 Die D

50-97 Template: ASTM D412 Die D

50-97 Template: ASTM D412 Die D

ASTM D412 Die C Tensile Specimens

May 13, 2015
Tensilkut Master Templates 50-92, 50-93 and 50-94 for preparing rubber test specimens in accordance with ASTM D412 Die C: Available for use on Tensilkut I and Tensilkut II models.

Tensilkut Master Templates 50-92, 50-93 and 50-94 for preparing rubber test specimens in accordance with ASTM D412 Die C: Available for use on Tensilkut I and Tensilkut II models.

50-94 Tensilkut Template for ASTM D412 Die C

50-94 Tensilkut Template for ASTM D412 Die C

50-93 Tensilkut Template

50-93 Template: ASTM D412 Die C

50-92 Template

50-92 Template

ASTM D695 Compression Testing

May 13, 2015

Preparing the ASTM D695 Specimen for compression testing is a two step process.  First, the gauge section must be cut in the blank, using one of the Tensilkut Master Templates designed specifically for this purpose.

50-82 Tensilkut Template for preparing the gauge section in ASTM D695 Compression specimens

50-82 Tensilkut Template for preparing the gauge section in ASTM D695 Compression specimens

 

After the gauge section has been cut, the specimen is inserted into the Tensilkut Master Template which cuts the ends square and parallel at 3.13″, in accordance with ASTM D695.  Different templates are available for  Tensilkut I and Tensilkut II machines.

50-89 Tensilkut Master Template for cutting the ends of the compression specimen square and parallel

50-89 Tensilkut Master Template for cutting the ends of the compression specimen square and parallel

50-88 Tensilkut Master Template for cutting the ends of the ASTM D695 compression specimen square and parallel

50-88 Tensilkut Master Template for cutting the ends of the ASTM D695 compression specimen square and parallel

50-87 Tensilkut Master Template for cutting the ends of the ASTM D695 compression specimen square and parallel: for use on the 10-20 or 10-40 series Tensilkut I or 10-82 Tensilkut II

50-87 Tensilkut Master Template for cutting the ends of the ASTM D695 compression specimen square and parallel: for use on the 10-20 or 10-40 series Tensilkut I or 10-82 Tensilkut II

Flexural Specimen Preparation

May 11, 2015

For .500″ wide strips, Tensilkut Master Templates will prepare specimens in accordance with ASTM D790.

50-72 Tensilkut Master Template for preparing .500" wide ASTM D790 specimens

50-72 Tensilkut Master Template for preparing .500″ wide ASTM D790 specimens

Tensilkut Master Templates for preparing ASTM D790 flexural specimens using all available Tensilkut I and Tensilkut II machines.

Tensilkut Master Templates for preparing ASTM D790 flexural specimens using all available Tensilkut I and Tensilkut II machines.

50-73 Tensilkut Master Template for preparing .500" wide ASTM D790 specimens

50-73 Tensilkut Master Template for preparing .500″ wide ASTM D790 specimens

50-74 Tensilkut Master Template for preparing .500" wide ASTM D790 specimens

50-74 Tensilkut Master Template for preparing .500″ wide ASTM D790 specimens

 

Also available: Templates for preparing 1″ ASTM D790 flexural specimens.

50-77 Tensilkut Template for 1.000" wide flexural specimens in accordance with ASTM D790: for use on 10-20 and 10-40 series Tensilkut I and 10-82 Tensilkut II

50-77 Tensilkut Template for 1.000″ wide flexural specimens in accordance with ASTM D790: for use on 10-20 and 10-40 series Tensilkut I and 10-82 Tensilkut II

Tensilkut Master Templates for preparing 1.000" wide flexural bars in accordance with ASTM D790 are available for use on all Tensilkut I and Tensilkut II models

Tensilkut Master Templates for preparing 1.000″ wide flexural bars in accordance with ASTM D790 are available for use on all Tensilkut I and Tensilkut II models.

50-78 Tensilkut Template for 1.000" wide flexural specimens in accordance with ASTM D790

50-78 Tensilkut Template for 1.000″ wide flexural specimens in accordance with ASTM D790: for use on 10-30 and 10-58 series Tensilkut I and 10-85 Tensilkut II

50-79 Tensilkut Template for 1.000" wide flexural specimens in accordance with ASTM D790

50-79 Tensilkut Template for 1.000″ wide flexural specimens in accordance with ASTM D790

ASTM D1822 Type L Tensile Impact Bars

May 11, 2015

Master Templates for preparing ASTM D1822 Type L Tensile Impact bars for use with the Tensilkut I and Tensilkut II:

50-69 ASTM D1822 Type L Tensilkut Master Template: for use with 10-68 or 10-78 Tensilkut I or 10-88 Tensilkut II

50-69 ASTM D1822 Type L Tensilkut Master Template: for use with 10-68 or 10-78 Tensilkut I or 10-88 Tensilkut II

50-68 Tensilkut Master Template in accordance with ASTM D1822 Type L

50-68 Tensilkut Master Template in accordance with ASTM D1822 Type L

Templates for preparing ASTM D1822 Type L specimens on all available Tensilkut I and Tensilkut II models

Templates for preparing ASTM D1822 Type L specimens on all available Tensilkut I and Tensilkut II models

50-67 Tensilkut Master Template for preparing ASTM D1822 Type L Tensile Impact Specimens

50-67 Tensilkut Master Template for preparing ASTM D1822 Type L Tensile Impact Specimens

ASTM D1822 Type S Tensile Impact Bars

May 11, 2015

ASTM D1822 Type S Tensile Impact bars are typically used when the available material is too small to prepare traditional impact bars.  Tensilkut Engineering has a master template to fit every Tensilkut I and Tensilkut II machine which will easily prepare these test bars.

50-64 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars on 10-68 or 10-78 Tensilkut I and 10-88 Tensilkut II models

50-64 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars on 10-68 or 10-78 Tensilkut I and 10-88 Tensilkut II models

50-63 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars on select Tensilkut I and Tensilkut II models

50-63 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars on select Tensilkut I and Tensilkut II models

50-62 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars

50-62 Tensilkut Master Template for preparing ASTM D1822 Type S tensile impact bars

ASTM D638 Type III Templates

May 11, 2015
The 50-57 Template for preparing ASTM D638 Type III tensile bars on the 10-20 or 10-40 series Tensilkut I or 10-82 Tensilkut II

The 50-57 Template for preparing ASTM D638 Type III tensile bars on the 10-20 or 10-40 series Tensilkut I or 10-82 Tensilkut II

The family of Tensilkut Master Templates available for preparing tensile bars in accordance with ASTM D638 Type III on all available Tensilkut I and Tensilkut II model machines

The family of Tensilkut Master Templates available for preparing tensile bars in accordance with ASTM D638 Type III on all available Tensilkut I and Tensilkut II model machines

The 50-58 Template for preparing ASTM D638 Type III tensile bars on the 10-30 series or 10-58 Tensilkut I or 10-85 Tensilkut II

The 50-58 Template for preparing ASTM D638 Type III tensile bars on the 10-30 series or 10-58 Tensilkut I or 10-85 Tensilkut II

The 50-59 Template for preparing ASTM D638 Type III tensile bars on the 10-68 or 10-78 Tensilkut I or 10-88 Tensilkut II

The 50-59 Template for preparing ASTM D638 Type III tensile bars on the 10-68 or 10-78 Tensilkut I or 10-88 Tensilkut II